Hola a todos, por el solo hecho de tener una ocasión muy especial, para festejar, no contando con una mesa, porque todavía no me la entregaron, luego de haberla comprado, entonces recurrí en reciclar una, quedando la misma una ves armada como se ve en la foto.
Así que lo primero es contar con el material adecuado, bueno en en este caso, buscando en la terraza pude dar con un caño de una pulgada de galvanizado, los cuales los utilizaría para la parte de las partes de la mesa antes mencionada.
Bueno cortando el mismo en una medida de 75 centímetros, para los largueros y costados, utilice hierro que me quedo cuando se desarmo una repisa, los cuales a lo largo los corte de 1,70 cm. de largo por 90 cm. de ancho.
La madera a utilizar, es la que había utilizado, cuando se armo el andamio, para cuando se revoco las paredes del departamento.
por supuesto las tuve que lijar, para que queden bien.
Teniendo todo preparado, comencé armar para luego ir soldando bien todo, en esta parte meta lo que seria las patas a presión, luego soldé un poco quedando perfecto todo.
Por supuesto como dije utilizando las herramientas adecuadas, como por ejemplo la escuadra imantada, la cual es de una gran ayuda para estos casos.
Teniendo todo presentado, les doy unas puntadas, luego de armar, termino de soldar bien todo.
Como veran ya va tomando forma dicha mesa, al estar soldado los largueros, para después acoplarlo con los que definen el ancho de la mesa.
De a poco al ir presentando le daba una puntada, para que quede bien formado, como podrán ver en la foto.
Como les comente, referente a las patas, las cuales es con caño galvanizado, soldado con el resto de los hierros.
Para que quede bien prolijo, siempre tengo por costumbre el de utilizar el nivel de mano como lo pueden ver, también se reforzó en la parte del medio, así queda bien firme, por supuesto luego con el mantel queda como la primera foto de este post.
MUCHAS GRACIAS POR SEGUIRME Y LEERME, QUE TENGAN UN EXCELENTE DIA EN FAMILIA.
ENGLISH
Hello everyone, just because I had a very special occasion to celebrate, not having a table, because I still did not get it, after having bought it, then I resorted to recycle one, being the same once assembled as seen in the photo.
So the first thing is to have the right material, well in this case, looking on the terrace I could find a one inch galvanized pipe, which I would use for the parts of the table mentioned above.
Well cutting the same in a measure of 75 centimeters, for the stringers and sides, I used iron that I had left when I disassembled a shelf, which in length I cut 1.70 cm. long by 90 cm. wide.
The wood to use, is the one I had used, when the scaffolding was assembled, for when the walls of the apartment were plastered.
Of course I had to sand them to make them look good.
Having everything ready, I started to assemble and then weld everything well, in this part I put what would be the legs to pressure, then I welded a little and everything was perfect.
Of course as I said using the right tools, such as the magnet square, which is a great help for these cases.
Having everything presented, I give them a few stitches, after assembling, I finish welding everything well.
As you can see, the table is already taking shape, as the beams are welded, and then I join it with the ones that define the width of the table.
Little by little, as I was presenting the table, I would stitch it, so that it would be well formed, as you can see in the photo.
As I mentioned, regarding the legs, which is with galvanized pipe, welded with the rest of the irons.
To make it neat, I always have the habit of using the hand level as you can see, it was also reinforced in the middle, so it is very firm, of course then with the tablecloth is like the first picture of this post.
THANK YOU VERY MUCH FOR FOLLOWING ME AND READING ME, HAVE A GREAT DAY WITH YOUR FAMILY.