Pozdrav majstori i prijatelji. Danas cu da vam nesto kazem o izolaciji kuce, i to najosetljivijem delu a to je potkrovlje kuce. U danasnje vreme sve vise dajemo paznju na izolaciju kuca. Duge i hladne zime i jako topla leta, uz sad sa krizom energenata izolacija kuca je veoma vazna, kao i dobri prozori i vrata.
Hello masters and friends. Today I will tell you something about the insulation of the house, and the most sensitive part and that is the attic of the house. Nowadays, we are paying more and more attention to the insulation of houses. Long and cold winters and very hot summers, with now with the crisis energy insulation of houses is very important, as well as good windows and doors.
Pozvao me je drug da pogledam problem u sobi, i pored toga sto je zamenio prozor i popravio krov kuce, vlaga i plesan se uporno vraca. Zbog nemogucnosti postavljanja izolacije sa spoljne strane ne pristupacan teren, odlucili smo da odradim izolacije u sobi na dva spoljna zida. Ranije sam to radio na par kuca pa je ovo bilo jedino resenje.
A friend invited me to look at the problem in the room, and despite replacing the window and repairing the roof of the house, the moisture and mold kept coming back. Due to the impossibility of installing insulation on the outside of the inaccessible terrain, we decided to do insulation in the room on two external walls. I used to do it on a couple of houses so this bill is the only solution.
Kupio sam material: stiropor, mrezicu, lepak, lajsne pvc, glet masu, boju, brusni papir, podlogu, silikon, stiropor lajsne, zastitnu foliju za pod i namestaj. Zastitio sam pod io namestaj sa folijom jer dva ormana i krevet nismo mogli da iznesemo. Zidove sam oljustio, sve sto je islo dole skinulo se, ocistio zidove sa metlom, iserao zid sa spahlom i namazao podlogu na zid.
I bought the material: styrofoam, mesh, glue, pvc moldings, smoothing compound, paint, sandpaper, substrate, silicone, styrofoam moldings, protective foil for the floor and furniture. I protected the floor and furniture with foil because we couldn't take out two closets and a bed. I peeled off the walls, took off everything that went down, cleaned the walls with a broom, scraped the wall with a spatula and smeared the base on the wall.
Po susenju podloge, ispunio sam rupe i neravnine sa lepkom za stiropor, i naneo jedan sloj lepka na zid sa spahlom i hoblom. Podloga se pravi u odnosu sa vodom 8:1, a lepak se dodaje u kanti sa vodom i mesa mesacem za lepak.
After drying the base, I filled the holes and irregularities with styrofoam glue, and applied one layer of glue to the wall with a spatula and a hob. The base is made in a ratio of 8: 1 with water, and the glue is added to the bucket of water and meat with a glue mixer.
Po susenju zida, lepe se stiropor ploce, lepak se nanosi po rubovima cele ploce i tri "krofne" po sredini table. Potreban alat: spahla, hobla, skalpel, metar, libela. Sutra dan nanosi se mrezica I lepak. Prvo se nanosi lepak na stiropor, pa zatim mrezica. Mrezica se utapa u lepak. Po susenju lepka nanosi se jos jedan sloj lepka.
After the wall dries, the styrofoam board is glued, the glue is applied along the edges of the whole board and three "donuts" in the middle of the board. Tools needed: spahla, planer, scalpel, meter, spirit level. The next day the mesh and glue are applied. Styrofoam glue is applied first, then mesh. The mesh is dipped in glue. After the glue dries, another layer of glue is applied.
Mrezica se prepusta na susedni zid, da nebi pucao sastav stiropora. Voditi racuna o struji. Ne pokrivati razvodne kutije i ako je moguce izvuci uticnice. Kada je osusi lepak, nanosi se glet mass u 2 3 sloja, po susenju glet mass zidove obrusiti brusnim papirom. Glet masa se pravi u kanti dodavanjem glet mase u vodi i mesanjem mesacem. Ostavi se masa 10 minuta da odstoji pa opet promesati. Nanosi se spahlom i hoblom.
The mesh is left on the adjacent wall, so as not to shoot the composition of styrofoam. Take care of electricity. Do not cover junction boxes and unplug if possible. When the glue dries, apply the smoothing mass in 2 3 layers, after drying the smoothing mass, sand the walls with sandpaper. Smooth mass is made in a bucket by adding smoothing mass in water and mixing with a mixer. Leave the mass to stand for 10 minutes, then stir again. It is applied with a spatula and a planer.
Na red dolazi bojenje zidova. Koristio sam belu boju BK Pol Protect, boja koja je namenjena protiv plesni. Naneo sam u dva sloja. Po susenju prvog sloja ide drugi sloj.
It's time to paint the walls. I used BK Pol Protect white paint, a paint that is intended against mold. I applied in two coats. After drying the first layer, the second layer follows.
Kada se osusila boja na red je doslo lepljenje stiropor lajsni. Lajsne se lepe sa akrilnim silikonom, uz pomoc pistolja za silikon. Na kraju lajsne se boje istom bojom.
When the paint dried, it was time to glue the styrofoam moldings. The moldings are glued with acrylic silicone, with the help of a silicone gun. At the end of the moldings are painted the same color.
Eto dragi majstori i prijatelji opisao sam ceo postupak. Nadam se da ce nekom da koristi. Pisite, pitajte sta vas zanima.
Pozdrav od Ujke.
Here, dear masters and friends, I have described the whole procedure. I hope it will benefit someone. Write, ask what interests you.
Greetings from Uncle.